Cartographer 3D
  • Welcome
  • 🗺️Cartographer Probe
    • Scan vs Touch Modes
    • 🏗️Installation and Setup
      • Before You Begin
      • Hardware Setup
        • CAN Termination
        • Stealthburner CW2 Mount
        • Wiring Diagrams
      • Software Configuration
        • Klipper Setup
        • Klipper Configuation
        • Calibration
        • Print Start Macro
        • First Print
        • Migrating from Cartographer to Scanner
      • Creality K1 & K1 Max Specific
      • Qidi Specific Installation Instructions
    • 📐Fine Tuning
      • Cartographer Models
      • Temperature Differential Calibration
      • Useful Macros
      • Extras
    • ♻️Firmware
      • Broken Katapult Bootloader
      • CANBUS Bitrate Switching
      • Firmware Switching
        • CANBUS to USB
        • USB to CANBUS
      • Firmware Updating
        • via Katapult
          • USB Flash
          • CANBUS Flash
        • via DFU
      • Manual Methods
        • ⬆️Firmware
        • Update or Re-Flash via ST-Link
        • Switching between CAN and USB Operation (v3 only)
        • Cartographer with Input Shaper
          • Update via Katapult (recommended)
          • Update via DFU Mode
        • Archive
          • Katapult
          • Re-Flashing Firmware
          • Cartographer (rp2040)
            • DFU / U2F Bootloader Mode
          • Which Firmware?
            • Cartographer v1 (RP2040 based probe)
            • Cartographer v2 or v3 w/ Input Shaper (USB/CAN)
              • Old Firmware
          • Update via STLink
    • ⚙️Settings & Commands
    • 😭Troubleshooting
    • 🆘Need Assistance?
    • 🔗Useful Links
    • ⁉️FAQ
    • 🔧Assembly
      • Standard
      • Low Profile
      • Right Angle
    • Archive
      • v1 (RP2040 Based Probes)
        • Klipper Configuration
        • Calibration
      • Classic Installation
        • Klipper Setup
        • Klipper Configuration
        • Calibration
      • Scan Based Calibration
  • 🚠Cartographer CNC Mount
    • 🚧Installation
  • 🌪️Linear Motor
    • 🗓️Coming Soon
Powered by GitBook
On this page
  • Step 1. Visit Here for the DFU flashing guide.
  • Step 2. Once Flashed
  • Step 3. All Done
  • Optional Step: Survey Touch
  • Katapult Bootloader will now be fixed for future flashing and DFU will not be required unless another issue arises with Katapult.
  1. Cartographer Probe
  2. Firmware

Broken Katapult Bootloader

Last updated 5 months ago

There are some Cartographer V3 ADXL probes that were shipped with a broken version of katapult. Unfortunately this means that when you go to update firmware via Katapult, the device wont be able to enter katapult mode for flashing. Fixing it is quite simple.

Step 1.

Step 2. Once Flashed

If you chose FULL CANBUS, unplug the cable and plug Cartographer into your CANBUS cable.

If you chose FULL USB, unplug and re-plug into USB cable.

Step 3. All Done

Optional Step: Survey Touch

If you want to use Survey Touch you will need to do some extra steps.

  • For USB,

  • For CANBUS,

Katapult Bootloader will now be fixed for future flashing and DFU will not be required unless another issue arises with Katapult.

🗺️
♻️
Visit Here for the DFU flashing guide.
Check out this guide on updating firmware to Survey Touch mode.
Check out this guide on updating firmware to Survey Touch mode.