Cartographer 3D
  • Welcome
  • 🗺️Cartographer Probe
    • Scan vs Touch Modes
    • 🏗️Installation and Setup
      • Before You Begin
      • Hardware Setup
        • CAN Termination
        • Stealthburner CW2 Mount
        • Wiring Diagrams
      • Software Configuration
        • Klipper Setup
        • Klipper Configuation
        • Calibration
        • Print Start Macro
        • First Print
        • Migrating from Cartographer to Scanner
      • Creality K1 & K1 Max Specific
      • Qidi Specific Installation Instructions
    • 📐Fine Tuning
      • Cartographer Models
      • Temperature Differential Calibration
      • Useful Macros
      • Extras
    • ♻️Firmware
      • Broken Katapult Bootloader
      • CANBUS Bitrate Switching
      • Firmware Switching
        • CANBUS to USB
        • USB to CANBUS
      • Firmware Updating
        • via Katapult
          • USB Flash
          • CANBUS Flash
        • via DFU
      • Manual Methods
        • ⬆️Firmware
        • Update or Re-Flash via ST-Link
        • Switching between CAN and USB Operation (v3 only)
        • Cartographer with Input Shaper
          • Update via Katapult (recommended)
          • Update via DFU Mode
        • Archive
          • Katapult
          • Re-Flashing Firmware
          • Cartographer (rp2040)
            • DFU / U2F Bootloader Mode
          • Which Firmware?
            • Cartographer v1 (RP2040 based probe)
            • Cartographer v2 or v3 w/ Input Shaper (USB/CAN)
              • Old Firmware
          • Update via STLink
    • ⚙️Settings & Commands
    • 😭Troubleshooting
    • 🆘Need Assistance?
    • 🔗Useful Links
    • ⁉️FAQ
    • 🔧Assembly
      • Standard
      • Low Profile
      • Right Angle
    • Archive
      • v1 (RP2040 Based Probes)
        • Klipper Configuration
        • Calibration
      • Classic Installation
        • Klipper Setup
        • Klipper Configuration
        • Calibration
      • Scan Based Calibration
  • 🚠Cartographer CNC Mount
    • 🚧Installation
  • 🌪️Linear Motor
    • 🗓️Coming Soon
Powered by GitBook
On this page
  • CANBUS or USB
  • Whats Required?
  • CANBus Katapult Updating
  • Step 1. Plug Cartographer in via CANBUS
  • Step 2. Get Your UUID
  • Step 2. SSH into Device & Run Script
  • Step 3. Select Katapult - Can Menu
  • Step 3. Find Your Device
  • Step 4. Find Your Device pt2
  • Step 5. Find Latest Firmware
  • Step 6. Flash Firmware
  • Step 7. Device Flashing
  • Step 8. All Done
  1. Cartographer Probe
  2. Firmware
  3. Firmware Updating
  4. via Katapult

CANBUS Flash

Last updated 4 months ago

CANBUS or USB

  • If you ordered a USB flashed cartographer, you use the

  • If you ordered a CAN flashed cartographer, you use the

Whats Required?

  • Cartographer Probe

  • Canbus to JST-PH Cable (For Katapult Canbus Flashing)

Using the scripts below, you may need to use the Install Prerequisites option first to make sure everything is configured prior to flashing.

CANBus Katapult Updating

Step 1. Plug Cartographer in via CANBUS

Step 2. Get Your UUID

This method requires prior knowledge of your CANBUS UUID.

This should have been supplied to you in your hardware box if purchased (insert date).

If you do not have your UUID. Visit to get it.

Step 2. SSH into Device & Run Script

~/cartographer-klipper/scripts/firmware.py -f can

Step 3. Select Katapult - Can Menu

Step 3. Find Your Device

Step 4. Find Your Device pt2

Step 5. Find Latest Firmware

Your CANBUS bitrare (if configured on your host device) should be detected and displayed. You should flash your cartographer with MATCHING bitrate firmware.

Step 6. Flash Firmware

Step 7. Device Flashing

Step 8. All Done

🗺️
♻️
USB Katapult Method
CANBUS Katapult Me
thod
Screen #1 - Canbus Detected
HERE